Home » Products » Frames » Campfire Quads CF1 X or SX Race Frame

Campfire Quads CF1 X or SX Race Frame

$60.00

Earn 60 points when you purchase this item

SKU: N/A Categories: , Tags: ,

Description

Campfire Quads CF1 X or SX Race Frame

Features:

  • Easy swap system and interchangeable arms

Simply remove the 40×40 screw, loosen the stack screw, and the arm slides right out. Press nuts in the mid plate keep the flight stack intact while you remove the damaged arm or swap between a stretch and true-x.

  • Motor protection and support for under-the-arm motor wires

Each arm has a 5mm slot at the end (as opposed to a closed hole) to give pilots the option of running their motor wires under the arms with no desoldering of wires required when replacing an arm. This doubles as motor protection and helps keep dirt out of the motor while still supporting the easy swap system.

  • Aerodynamic pod with VTX access and an integrated antenna mount

Every frame comes with a pod with built-in support for two popular UFL/MMCX antennas: Luminier AXII and TrueRC AXII *

HD, SMA “Rocketman”, and Foxeer Predator camera specific pods as well as a GoPro Session case are available through Phoenix3D!

  • Durability

Designed to be as light as possible without sacrificing durability. In the event of failure arms are meant to break away from the motors and pod to prevent damage to the electronics. Tight fitting arm slots and press nuts also help mitigate the need to re-tighten screws after a crash.

Our standard pod was created in collaboration with Mayday FPV and is printed in Nylon; a much harder material than TPU that is also lighter, dye-able to pilot preference, and grants better protection for your equipment against trees, prop strikes, or other quads.

  • Low cost replacement parts

Replacement arms, pods, battery pads, and frame accessories are offered at low prices to keep you in the air without breaking the bank.

  • Built in battery strap slots

A simple feature, but one that many frames overlook. Not only did we add slots to the bottom plate but you have two options of where to run the strap: Between the arms or under the ESC.

  • Support for 30×30 and 20×20 stacks

Available in true X and SX configurations.

True X Specifications:

  • ~75g with hardware and pod
  • Frame size – ~206mm
  • Bottom plate – 2mm
  • Mid plate – 2mm
  • Arms – 5mm
  • Hardware – 12.9 steel (screws) and Stainless steel (press nuts)
  • Pod material – 3D printed Nylon
  • Camera support – Micro (Foxeer or Runcam)
  • Camera angles – 30-60 degrees
  • Motor support – 16×16 and 16×19
  • True X supports up to 5.1″ props

SX Specifications:

  • ~77g with hardware and pod
  • Frame size – ~206mm
  • Bottom plate – 2mm
  • Mid plate – 2mm
  • Arms – 5mm
  • Hardware – 12.9 steel (screws) and Stainless steel (press nuts)
  • Pod material – 3D printed Nylon
  • Camera support – Standard Size Micro
  • Camera angles – 30-60 degrees
  • Motor support – 16×16 and 16×19
  • Stretched X supports up to 5.5″ props

What’s included:

  • Nylon Pod
  • 5 Carbon fiber arms, 1 bottom plate, and 1 mid plate
  • Foam battery pad
  • 4 – M3 30mm steel screws (For 30×30 stack use)
  • 4 – M3 16mm steel screws
  • 4 – M3 12mm steel screws (Replaces the 30×30 stack screws if using 20×20 stack)
  • 4 – M3 6mm steel screws
  • 4 – M3 10mm aluminum standoffs
  • 8 – M3 press nuts
  • 2 – M2 6mm screws for camera mounting
Replaceable Arms available HERE

Recommended Equipment:

Additional information

Weight 66.0000 g
Dimensions 175.0000 x 118.0000 x 19.0000 mm
Frame

,

%d bloggers like this: